Your disposal hums but won't spin โ the impeller plate is jammed. It's completely silent when you flip the switch โ the thermal overload protector has tripped or the motor has failed. Water drips from the sink collar โ the sink mounting gasket has deteriorated. Each of these is a different diagnosis, and each has a different solution. Masters Plumbing Service's techs in Sheldon, TX arrive with the jamming tools, reset wrench, and replacement units to resolve any disposal failure same visit.
๐ Call +1-855-718-1500 โ Same-Day Service
Garbage disposal failures have specific, diagnosable causes. Our techs don't just swap units โ they identify what failed and whether repair or replacement is the right call for your situation.
A disposal that hums but won't spin almost always just needs the jam cleared with an Allen wrench at the center socket and the reset button pressed โ a 5-minute fix that doesn't require a new unit.
InSinkErator models use a 1/4-inch Allen wrench at the center bottom; Waste King models use a broom-handle approach at the top. Knowing which you have before arriving saves time and prevents the wrong tool damaging the motor shaft.
A disposal that jams once is worth clearing and resetting. A disposal that jams repeatedly, has a seized turntable bearing, emits burning smells, or is over 10 years old is likely approaching motor failure โ and the repair cost of a failed motor exceeds the cost of a new unit.
A disposal isn't an isolated appliance โ it connects to the sink drain, the dishwasher drain (if present), and the drain arm leading to the p-trap. We inspect the full connection set during any disposal call: drain arm slope, dishwasher drain knockout (if a dishwasher is being added), and p-trap connection integrity.
Most disposal calls complete in 30โ60 minutes โ same visit, flat-rate pricing.
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris โ we distinguish between the two before recommending replacement.
If power is confirmed at the disposal and it still won't start after a reset, the motor is failed. We then move to the replacement conversation with honest cost comparison.
Disposal leaks come from three locations: the sink flange (top of the unit where it mounts to the sink drain opening โ repaired by re-sealing the flange with plumber's putty and re-tightening the mounting ring), the side port (dishwasher drain hose connection โ usually a loose hose clamp or cracked fitting), or the bottom of the unit (internal body crack or failed internal seal โ indicates replacement needed).
If the turntable bearing has failed โ indicated by a loud rumbling throughout operation rather than specific impact sounds โ that's an internal motor wear failure that warrants replacement.
If the slow drain persists after cleaning the drain arm and p-trap, a camera scope of the kitchen drain line is the next step to check for blockage further downstream.
When the motor has failed, the unit body is cracked, or the existing unit is underpowered for the household's use pattern, we replace the disposal with a new unit matched to the sink drain configuration. We carry 1/2 HP, 3/4 HP, and 1 HP units from InSinkErator and other major brands on our trucks for same-day installation.
No guesswork โ we diagnose before we quote, and quote before we start.
If you know the disposal is over 10 years old, tell us โ that changes how we approach the repair-vs-replace conversation upfront.
For leaks, we dry the area completely and run a short test cycle to confirm exactly which connection is dripping.
You receive a flat-rate price for the repair option and, if relevant, the replacement option with unit cost included. For a simple jam clear, that's a single, low line item. For a failed motor, we show you the new unit cost and installation price together.
We leave the cabinet dry and the disposal running quietly. If a dishwasher drain hose was involved, we run a dishwasher cycle to verify no backup occurs.

The disposal under our kitchen sink was 12 years old and started leaking from the bottom โ which the tech explained is always an internal seal failure, not a repairable condition. He had a replacement 3/4 HP InSinkErator on his truck, installed it in about 45 minutes, and the kitchen is back to normal. Old unit got pulled, new unit tested clean, no leaks at any connection.
After we added a dishwasher, it started backing up every cycle. Masters Plumbing Service found the problem immediately โ the previous installer had forgotten to knock out the dishwasher drain plug inside the disposal inlet. The plug was blocking the drain port. Two-minute fix. The tech also tightened the dishwasher drain hose clamp, which was loose. Never had another backup.
Old disposal stopped working completely โ no hum, nothing. I assumed the motor failed. The tech checked the wiring first โ found a loose wire nut at the junction box under the sink that had vibrated loose over the years. Reconnected the wire, reset the overload button, disposal came right on. Would have been embarrassing if I'd bought a replacement unit. Masters Plumbing Service's thoroughness saved me a few hundred dollars.

Our trucks carry replacement disposal units in common horsepower ratings for same-day installation when the motor has failed.

Call now โ same-day service available in Sheldon and across Sheldon, TX.
๐ Call +1-855-718-1500 Now